Resolving Komatsu PC200-8 Cylinder Liner Failure in Indonesia: A Technical Sourcing Report
This technical sourcing report examines a cylinder liner failure on a Komatsu PC200-8 excavator operating in Indonesia's coal mining sector. It details the diagnostic process, compatibility verification, and the procurement solution through MechLink, emphasizing nameplate matching and risk reversal to minimize downtime.

Incident Background / Problem Statement
A contracting company running a fleet of Komatsu PC200-8 excavators at an open-pit coal mine in East Kalimantan, Indonesia, reported sudden engine power loss, white smoke, and coolant contamination on one of its primary production units. The machine had logged approximately 11,400 operating hours. On-site technicians traced the fault to a scored cylinder liner in engine serial number SAA6D107E-1-10253, with the OEM cylinder liner part number 6215-21-8010 exhibiting deep vertical scoring and cavitation erosion. The associated piston had partially seized, requiring a complete liner and piston assembly replacement. Downtime reached 72 hours, costing the operation an estimated USD 2,100 per day in lost production and idle crew.
Answer Block The root cause was abrasive wear aggravated by high-sulfur diesel and marginal coolant pH control, leading to liner scuffing and cavitation. Successful replacement demanded exact dimensional and metallurgical compliance.
- Confirm OEM number 6215-21-8010 via engine nameplate cross-reference for the SAA6D107E-1 variant used in the PC200-8.
- Verify bore diameter 120.00–120.04 mm, chrome-plated liner surface hardness ≥ 60 HRC, and piston-to-liner cold clearance 0.05–0.08 mm.
- Source from verified inventory with full traceability, original packaging, and batch documentation to avoid counterfeit liners common in the region.
Technical Diagnosis and Compatibility Checklist
The high ambient dust and humidity of Indonesian mining sites, combined with high-sulfur diesel (often >2,000 ppm in domestic supply), create an environment where sulfuric acid forms in the combustion chamber and attacks the liner surface. Inadequate coolant maintenance, especially low nitrite levels or high chloride content, accelerates liner cavitation erosion on the water jacket side. For the Komatsu PC200-8’s 6-cylinder SAA6D107E-1 engine, the liner must withstand a peak combustion pressure of 20 MPa and exhibit a surface roughness of Ra ≤ 0.4 µm after honing.
Verification checklist before ordering replacement:
- Engine serial number break: Early PC200-8 engines (before S/N E0015001) may use liner 6215-21-8010; later units might require 6240-21-8010. Always match to the engine nameplate.
- Liner flange thickness: Must measure 7.95–8.05 mm. Undersized flange causes low protrusion and head gasket leakage.
- Protrusion specification: With liner seated without O-rings, protrusion over crankcase deck must be 0.05–0.15 mm. Use a dial indicator across four points.
- Piston ring end gap: Install a new ring in the liner bore and measure gap; specification is 0.30–0.45 mm for top ring, 0.45–0.65 mm for second ring.
- OEM number verification: The forged or laser-etched number on the liner flange should read ‘6215-21-8010’ with a consistent font and Komatsu logo; check for hologram sticker on OEM packaging.
The Sourcing Resolution
The procurement was executed through MechLink’s global fulfillment system as a factual case study. Following the diagnostic checklist, the fleet manager provided the engine nameplate data, confirming the exact variant. MechLink’s quality control team performed nameplate matching: the engine serial number was cross-referenced with the Komatsu electronic parts catalog to ensure the correct cylinder liner revision (early vs. late production).
- Genuine verification: The identified stock carried the OEM hologram, batch code, and laser-etched number identical to the required 6215-21-8010. A photo of the physical nameplate was supplied before dispatch.
- Risk reversal policy: The transaction was covered by the “Buy Wrong, We Compensate” program, which guarantees a full refund including air freight if the part does not match the machine, a safeguard critical in remote mining areas.
- Logistics timeline: Ready stock was located in MechLink’s Singapore hub. Five-day express air freight delivered the liner kit directly to the mine site in Balikpapan, minimizing downtime to the absolute operational window.
Cost Drivers and Warranty Terms
Several factors determine the price of cylinder liner 6215-21-8010 in Indonesia:
- Genuine OEM vs. aftermarket: A genuine Komatsu liner set (including piston rings, circlips, and piston pin) typically ranges between USD 450 and USD 550 ex-works. Aftermarket equivalents, often made in India or China, can cost 40–60% less but may lack the chrome-plated surface hardening and precise flange thickness control.
- Material quality: OEM liners use centrifugally cast pearlitic gray iron with a chromium plating layer of 0.05–0.10 mm, providing a hardness of 60–65 HRC. Non-certified aftermarket liners may use lower-grade cast iron leading to accelerated wear under high-sulfur fuel.
- Import duties and freight: Air freight to remote Indonesian islands adds 20–30% to landed cost; clearance through customs requires proper Harmonized System code 8409.99.79.
Standard warranty terms: Genuine OEM liners carry a 12-month or 2,000-hour warranty against material and manufacturing defects when installed with new pistons and rings by certified technicians. Reputable aftermarket suppliers typically offer 6 months or 1,000 hours. Warranty does not cover failure due to abrasive ingestion, coolant neglect, or improper installation.
Q&A (Technical Focus)
Q: How do I verify the OEM number for a Komatsu PC200-8 cylinder liner? A: Locate the engine nameplate on the oil cooler housing or rocker cover. Note the engine model SAA6D107E-1 and the serial number. Using Komatsu’s electronic parts catalog (EPC), enter the serial number to retrieve the correct liner part number—most commonly 6215-21-8010 for early engines. This number is also laser-etched on the liner flange.
Q: What is the critical tolerance for cylinder liner protrusion on the PC200-8 engine? A: The liner protrusion above the crankcase deck must be 0.05–0.15 mm, measured with a dial indicator at four equally spaced points on the flange. Variation between adjacent liners should not exceed 0.03 mm to ensure uniform head gasket compression.
Q: Can I use an aftermarket cylinder liner if the genuine OEM part is unavailable? A: Yes, provided the aftermarket unit matches the exact bore geometry (120.00–120.04 mm), flange thickness (7.95–8.05 mm), and material specification (chrome-plated pearlitic iron, hardness ≥ 60 HRC). The supplier should furnish ISO/TS 16949 certification and documented batch test reports. Without these, run the risk of premature cavitation or seizure.
Q: How does Indonesia’s tropical climate affect cylinder liner life? A: High humidity and fine silica dust from overburden increase abrasive intake load, especially if air filtration is not maintained. Volcanic particulates can bypass worn filter elements and score the liner. Additionally, high ambient temperatures reduce charge air density, which may elevate exhaust gas temperatures and thermal stress on the liner. Strict air filter replacement intervals and coolant condition monitoring are essential.
CTA and Link
To verify part numbers and check real-time inventory for your equipment, prepare your Machine Nameplate and visit our official website for direct procurement support: https://www.mechandlink.com